diff --git a/boards/nucleo-l496zg/Makefile.dep b/boards/nucleo-l496zg/Makefile.dep
index 729485827299c1a63e12514b30d4943aeea41c0d..f41bf0f86b263ecbbc1cb43a2ac5d1112890672b 100644
--- a/boards/nucleo-l496zg/Makefile.dep
+++ b/boards/nucleo-l496zg/Makefile.dep
@@ -1 +1,3 @@
+FEATURES_REQUIRED += periph_lpuart
+
 include $(RIOTBOARD)/common/nucleo/Makefile.dep
diff --git a/boards/nucleo-l496zg/Makefile.features b/boards/nucleo-l496zg/Makefile.features
index ff74d0e79c79b7298643606f6f12dfbb895de0d8..67dc676d956511f6ba9751d7bf0bd1d76bec06c1 100644
--- a/boards/nucleo-l496zg/Makefile.features
+++ b/boards/nucleo-l496zg/Makefile.features
@@ -4,7 +4,7 @@ FEATURES_PROVIDED += periph_rtc
 FEATURES_PROVIDED += periph_rtt
 FEATURES_PROVIDED += periph_spi
 FEATURES_PROVIDED += periph_timer
-FEATURES_PROVIDED += periph_uart
+FEATURES_PROVIDED += periph_uart periph_lpuart
 
 # load the common Makefile.features for Nucleo boards
 include $(RIOTBOARD)/common/nucleo144/Makefile.features
diff --git a/boards/nucleo-l496zg/Makefile.include b/boards/nucleo-l496zg/Makefile.include
index a7612cbebaf7c55241bd02b8b61e26dac298642a..51050cea5be68fe92583f05fe58594adb8ff3170 100644
--- a/boards/nucleo-l496zg/Makefile.include
+++ b/boards/nucleo-l496zg/Makefile.include
@@ -4,7 +4,7 @@ export CPU_MODEL = stm32l496zg
 
 # stdio is not available over st-link but on the Arduino TX/RX pins
 # A serial to USB converter plugged to the host is required
-PORT_LINUX ?= /dev/ttyUSB0
+PORT_LINUX ?= /dev/ttyACM0
 PORT_DARWIN ?= $(firstword $(sort $(wildcard /dev/tty.usbmodem*)))
 
 # load the common Makefile.include for Nucleo boards
diff --git a/boards/nucleo-l496zg/include/periph_conf.h b/boards/nucleo-l496zg/include/periph_conf.h
index 851b9de54f762b14764e6c7e1f679a8fd04ca52e..0366faa80b7bbb5a4fc467dccec5fa70c0e1af7f 100644
--- a/boards/nucleo-l496zg/include/periph_conf.h
+++ b/boards/nucleo-l496zg/include/periph_conf.h
@@ -112,6 +112,18 @@ static const timer_conf_t timer_config[] = {
  * @{
  */
 static const uart_conf_t uart_config[] = {
+    {
+        .dev        = LPUART1,
+        .rcc_mask   = RCC_APB1ENR2_LPUART1EN,
+        .rx_pin     = GPIO_PIN(PORT_G, 8),
+        .tx_pin     = GPIO_PIN(PORT_G, 7),
+        .rx_af      = GPIO_AF8,
+        .tx_af      = GPIO_AF8,
+        .bus        = APB12,
+        .irqn       = LPUART1_IRQn,
+        .type       = STM32_LPUART,
+        .clk_src    = 0,
+    },
     {
         .dev        = USART3,
         .rcc_mask   = RCC_APB1ENR1_USART3EN,
@@ -130,8 +142,9 @@ static const uart_conf_t uart_config[] = {
     }
 };
 
-#define UART_0_ISR          (isr_usart3)
-#define UART_0_DMA_ISR      (isr_dma1_stream5)
+#define UART_0_ISR          (isr_lpuart1)
+#define UART_1_ISR          (isr_usart3)
+#define UART_1_DMA_ISR      (isr_dma1_stream5)
 
 #define UART_NUMOF          (sizeof(uart_config) / sizeof(uart_config[0]))
 /** @} */