To build OSv
============
0) Install perquisite packages:
On Fedora:
yum install boost-static genromfs libvirt
On Debian:
apt-get install libboost-all-dev genromfs libvirt
1) make sure all git submodules are uptodate
-----------------------------------------
git submodule update --init
2) build the specially patched libunwind
-------------------------------------
cd external/libunwind
autoreconf -i
sh config.sh
make
cp ./src/.libs/libunwind.a ../..
cd ../..
4) build the glibc test suite
cd external/glibc-testsuite
make
cd ../..
5) build osv
---------
make
To run OSv
==========
./scripts/run.py
External Networking
===================
To start osv with external networking:
$ sudo ./scripts/run.py -n
Inside OSv, configure netwroking like so:
$ ifconfig virtio-net0 192.168.122.100 netmask 255.255.255.0 up
$ route add default gw 192.168.122.1
Test networking:
$ test TCPExternalCommunication
Debugging
=========
To build with debugging symbols, and preemption off (to not confuse gdb),
make -j mode=debug conf-preempt=0
To clean debugging build's results, use
make clean mode=debug
To run the debugging build:
./scripts/run.py -d
To connect a debugger to this run:
$ gdb build/debug/loader.elf
(gdb) connect
(gdb) osv syms
(gdb) bt
To put a breakpoint early in the osv run, a useful trick is tell the vm to
reboot after setting the breakpoint:
(gdb) hbreak function_name
(gdb) monitor system_reset
(gdb) c
Tracing
=======
To add a static tracepoint, use the following code:
tracepoint<u64, int> trace_foo("foo", "x=%x y=%d");
...
void foo(u64 x, int y)
{
trace_foo(x, y);
...
}
Where
trace_foo: an internal identifier
"foo": a name for the tracepoint as will be visible in the log
<u64, int>: parameters for the tracepoint
"x=%x y=%d": format string for the tracepoint; size modifiers unneeded
To enable tracepoints at runtime, use the --trace= switch:
scripts/imgedit.py setargs build/release/loader.img --trace=sched\* testrunner.so
you can use multiple --trace= switches, or a single one with commas. Shell-style wildcards
allow enabling multiple tracepoints (as in the example).
To trace all function entries/returns in the program, build with conf-tracing=1 (clean build
needed), and enable "function*" tracepoints, with --trace=.
To view a trace, connect with gdb, and:
(gdb) osv syms
(gdb) set pagination off
(gdb) set logging on
(gdb) osv trace
gdb.txt will contain the the trace.
Leak Detection
==============
Memory allocation tracking can be enabled/disabled with the gdb commands
"osv leak on", "osv leak off", but even easier is to add the "--leak"
paramter to the loader, to have it start leak detection when entering the
payload (not during OSv boot). For example:
scripts/run.py -e "--leak java.so -jar cli.jar"
scripts/run.py -e "--leak tests/tst-leak.so"
Leak detection can be used in either the debug or release build, though
note that the release builds' optimizations may somewhat modify the
reported call traces.
When the run ends, connect to OSV with the debugger to see the where
the remaining allocation come from:
$ gdb build/release/loader.elf # or build/debug/loader.elf
(gdb) connect
(gdb) osv syms
(gdb) set logging on # optional, if you want to save the output to a file
(gdb) set height 0 # optional, useful if using "set logging on"
(gdb) osv leak show
Please note that "osv leak show" can take a L-O-N-G time - even a few
minutes, especially when running Java, as it allocates myriads of objects
that GDB will now have to inspect.
Use-after-free and overrun detection
====================================
Set conf-debug_memory=1 in base.mak, and perform a clean build. A use-after-free will result
in an immediate segmentation fault.
Note that the detector requires a lot of memory, so you may need to start a larger guest.
Running java benchmarks
=======================
After running "make", do
scripts/imgedit.py setargs build/debug/loader.img java.so -jar bench.jar
and then run normally (./scripts/run.py).
Profiling
=========
You can use 'perf kvm' for profiling:
perf kvm --guestvmlinux=build/release/loader.elf top
Nadav Har'El
authored
The existing shutdown() code only worked with AF_INET sockets, and returned ENOTSOCK for AT_LOCAL sockets, because we implemented the latter sockets in completely different code (in af_local.cc). So in uipc_syscalls_wrap.c, the same place we call a the special af-local socketpair(), we also need to call the special af-local shutdown(). The way we do it is a bit ugly, but effective: shutdown() first calls shutdown_af_local(), and if that returns ENOTSOCK (so it's not an af_local socket), we continue trying the regular socket shutdown code. A better way would have been to add shutdown() to the fileops table - either the generic one (why not?), or invent a new mechanism whereby certain file types (in this case, "sockets" of all types) can have additional ops tables including in this case a shutdown() operation. Linux has something of this sort for implementing shutdown().